產品列表PROUCTS LIST
新聞動態NEWS
- 蘭格ACHEMA 2024展會(huì )回顧:探尋精密流體傳輸市場新機遇
- 選擇皮升超微量注射泵時需要注意的點
- 分配型蠕動泵的工作原理可以概括為“擠壓和吸力”
- 關于多通道蠕動泵您了解多少?
- 灌裝蠕動泵的工作過程可以分為四個階段
- 灌裝蠕動泵是利用蠕動原理進行流體輸送的設備
- 再添強勢新成員!蘭格dLSP 501W數字型分體式注射泵正式上市
- 迭代升級!dPOFLEX ® 高精度灌裝分裝系統不斷迭代提升產品能力
- 從基本開始認識多通道灌裝系統
- 多通道灌裝系統的基礎知識
蘭格精密蠕動泵的使用常識
點擊次數:2180 更新時間:2017-04-10
今天我們就來詳細介紹下,讓您更加了解蘭格精密蠕動泵。
上一篇 注射泵灌裝系統可記憶設置的各種工作參數 下一篇 小型柱塞泵的日?;竟ぷ?/a>
蘭格精密蠕動泵在使用前,應該注意如下事項
1、對于蘭格精密蠕動泵啟動前應做一些必要的檢查:
2、泵軸的轉動情況是否正常,有無卡死現象。如果蠕動泵軟管是前次使用過的沒有更換,取出軟管,將泵頭擠壓的部分移開,以減少軟管的疲勞度,從而達到更好的傳輸效果。由于蠕動泵的集成度高,可控性好,其他主要開關通斷良好,則可以放心的使用了。
蘭格精密蠕動泵的使用注意要點:
1、*次使用蠕動泵的時候我們要先將調速的旋鈕進行調節,要調到zui小的位置上面.然后才可以接通電源,如果看到指示燈亮那就說明蠕動泵已經工作了,然而進行調節速度的旋鈕,正常后就可以使用了。
2、使用蠕動泵時調壓板不要擰太緊,以免“扎死”泵頭,一般調到有液體流出即可。
3、泵頭在快速運轉時,切勿按動“順/逆”開關,若要按動,則先將速度調慢,然后再將速度調至原來速度,即將電壓表讀數調至原來值。
4、蠕動泵在使用期間,應隨時注意硅膠管是否完好,一般在中速情況下運轉為佳,當發現硅膠管使用老化時,應及時更換硅膠管。當蠕動泵開始運轉時,硅膠管可能有向一端腫起現象,可用手拉直即可。
5、使用完畢要將泵頭清洗干凈,如果長時間不用,應取下硅膠管,以延長其使用壽命。硅膠管是易損物品,使用一段時間后請及時更換。不然會(huì )造成漏液,損壞儀器。