產品列表PROUCTS LIST
新聞動態NEWS
- 蘭格ACHEMA 2024展會(huì )回顧:探尋精密流體傳輸市場新機遇
- 選擇皮升超微量注射泵時需要注意的點
- 分配型蠕動泵的工作原理可以概括為“擠壓和吸力”
- 關于多通道蠕動泵您了解多少?
- 灌裝蠕動泵的工作過程可以分為四個階段
- 灌裝蠕動泵是利用蠕動原理進行流體輸送的設備
- 再添強勢新成員!蘭格dLSP 501W數字型分體式注射泵正式上市
- 迭代升級!dPOFLEX ® 高精度灌裝分裝系統不斷迭代提升產品能力
- 從基本開始認識多通道灌裝系統
- 多通道灌裝系統的基礎知識
如何正確地拆裝齒輪泵?
點擊次數:3427 更新時間:2020-10-24
一、拆卸
拆卸前應做好充分的準備工作,熟悉設備結構,工藝流程,運行狀態;拆卸時應小心謹慎,避免損壞設備零部件。
二、復查數據
對齒輪泵各部件配合間隙,應做全面檢查。
三、檢查
對拆下的零部件進行詳細檢查,對齒輪作著色檢查,不允許存在裂紋;軸頸的圓錐度合格,表面不得有劃痕,粗糙度Ra的大允許值為1.6μm;端蓋、托架、泵體不得有明顯缺陷。
四、修復或更換
對超標的零部件應予以更換,對需修復的零部件,修復后應符合標準。
五、組裝及調整
齒輪端面與端蓋,托架的軸向間隙,依靠改變端蓋,托架與泵體之間的密封墊片的厚度來調整;緊固端蓋螺栓時,用力對稱均勻,邊緊邊盤動轉子,遇到轉子轉不動時,應松掉螺栓重緊;加填料或裝油封時,緊壓蓋時仍需邊緊邊盤動轉子,不可緊得過死。
六、試車
水壓試驗為工作壓力的1.5倍,保持5min不漏,試車運行期間,無泄漏,運行聲音正常,無異常振動,出口壓力符合要求為合格。
上一篇 多通道灌裝系統實現所有通道同時同步注液分裝 下一篇 微型柱塞泵的核心技術